Hangzhou Epsole Machinery Co., Ltd. is one of the most reliable manufacturers and suppliers of eps styrofoam thermocol cutting machine in China. We warmly welcome you to buy high quality eps styrofoam thermocol cutting machine for sale here from our factory. Good service and reasonable price are available.
Operating instructions for EPS styrofoam thermocol cutting machine:
1. The operator is familiar with the performance and structure of the Eps styrofoam thermocol cutting machine tool, masters the operating procedures, and strictly abides by the rules and operation and maintenance procedures.
2. Non-designated personnel are not allowed to use the equipment casually, and there are measures in the room.
3. Before starting the machine tool, the following work should be done first:
1) Check whether all parts of the machine tool are in good condition, and adjust the level regularly. Add sufficient lubricating oil according to the lubrication regulations and fill the working fluid tank with saponified oil and water, keep it clean, and check whether the pipe joints are firm.
2) Check whether the connection between the machine tool and the control box is well connected, whether the input signal is consistent with the moving direction of the carriage, and adjust the high-frequency pulse power supply properly.
3) Check whether the vertical and horizontal strokes of the workbench are flexible, whether the reciprocating movement of the ball cylinder carriage is flexible, and move the thread roller carriage to the middle position where the travel switch is between the two baffles. The stopper of the travel switch should be adjusted within the required range, so as to prevent the thread rolling drum from being rushed out when the machine is turned on, causing the wire to be stripped. Clockwise off. In order to prevent the molybdenum wire from being broken due to the movement of the thread rolling drum carriage due to inertia, or even the screw nut from falling off. After the above checks are correct, the machine can be turned on.
4) Install the workpiece, place the workpiece to be cut on the mounting table and fix it with the pressure plate screw. When cutting the entire cavity, the workpiece and the mounting table cannot touch the wire frame. If cutting the die, the molybdenum wire should be installed through the workpiece The reserved holes on the board can only be cut after alignment.
5) When cutting the workpiece, first start the thread rolling cylinder, press the wire feeding button, wait for the guide wheel to rotate, then start the working fluid motor, and open the working fluid valve. If you stop during cutting or stop after processing, first turn off the frequency conversion, cut off the high-frequency power supply, and then turn off the working fluid pump. After the working fluid on the guide wheel is thrown off, then turn off the roller motor.
6) The working fluid should be kept clean and the pipeline unobstructed. In order to reduce the electric corrosion in the working fluid, foam plastics can be placed in the workbench, the return tank and the working fluid tank for filtration, and the working fluid tank and filter should be cleaned regularly. Change the working fluid.
7) Always keep the workbench carriage, ball screw and rolling guide rail clean, and do not allow dust to enter, so as not to affect the movement accuracy.
8) If the thread rolling cylinder shakes or vibrates when changing directions, stop using it immediately, check whether the relevant parts are loose, and adjust it in time.
9) Inject kerosene into the guide wheel bearing 1-2 times a week to keep it clean and service life.
10) Pay special attention to the maintenance of the console device and keep it clean.
11) Operators are not allowed to tamper with electrical components and console devices, stop the machine immediately if any problem is found, and notify the maintenance personnel to overhaul.
12) Cut off the power supply at the end of work or when leaving get off work, wipe all the machine tools and control devices, and keep them clean. It is best to cover all the computers with a cover, and clean the work site (to avoid flying dust), especially the guide rail sliding surface of the machine tool. , and refueling, do a good job of handover and operation records.
Hot Tags: Eps Styrofoam Thermocol Cutting Machine, China, manufacturers, suppliers, factory, price, vacuum, for sale, Cnc Hot Wire Cutter Cutting Machinery, Hotwire Foam Cutting Machine, EPS Foam Block Cutting Machine, Hotwire Cnc Foam Cutting Machine, EPS Basic cutting machine, EPS CNC Cutting Machine